Miele DA 3460 Manuale di Servizio

Operating and installation instructionsCooker hoodDA 3460, DA 3460 EXTDA 3480DA 3490, DA 3490 EXTTo avoid the risk of accidentsor damage to this appli

The cooker hood works with. . . air extraction:The air is drawn in, cleaned by thegrease filter and then directed outside.If the on-site ventilation s

Description of the appliance11

a Exhaust socket C 150 mmb Controlsc Grease filterd Pull-out deflector platee Hob lightingf Charcoal filter(extra accessory available to orderfor reci

The cooker hood is operated by pullingout and pushing in the deflector plate.To switch the fan on^Pull out the deflector plate.The fan will come on at

Automatic switch-off of the IntensivesettingYou can set the Intensive setting so thatit always only runs for 10 minutesbefore reverting automatically

,Before any cleaning ormaintenance work is carried out,disconnect the cooker hood from themains supply.,Exercise caution when changinghalogen lamps. T

ControlsThe controls may sufferdiscolouration or damage if soiling isleft on them for too long. Removesoiling straight away.Observe the General notes

Cleaning the grease filter by hand^Clean the filter with a soft nylon brushin a mild solution of hot water and alittle washing-up liquid.Do not use &q

Fitting and replacing thecharcoal filtersIf the cooker hood is connected forrecirculation, a charcoal filter (optionalaccessory) must be inserted in a

Changing a halogen lamp^Pull out the deflector plate, andremove the grease filter as describedearlier.^Switch off the fan and the lighting.,Exercise c

Caring for the environment...3Warning and Safety instructions ...4Description

In the event of a fault which you cannotcorrect yourself, or if the appliance isunder guarantee, please contact:–Your Miele Dealer / Chartered Agentor

DA 3460DA 3480Appliance dimensions21

DA 34901) The front section of the wall housingunit must be fitted with a shelf to thedepth of the partition wall.If the appliance is fitted further b

Installation accessoriesInstallation23

a 1 exhaust connectionfor exhaust ducting C 150 mm.b 1 reducing collarfor exhaust ducting C 125 mm.c 1 non-return valvefor fitting into the exhaust co

Installation25

Positioning the appliance inthe wall housing unitTo position the appliance correctly,cut the spacer strip to required depthT, and then attach it to th

^Screw the brackets onto the right andleft inside walls of the housing unit asshown. The back edge of thebrackets should align with the verticalline d

^When fitting an 80 cm or a 90 cmappliance into a 60 cm unit, unscrewthe brackets on the deflector platewhilst it is pulled out.^Lift the appliance up

^Remove the protective film betweenthe deflector plate and the casing.^ Secure the front of the appliance tothe floor of the housing unit frombelow us

Disposal of the packing materialThe transport and protective packinghas been selected from materials whichare environmentally friendly fordisposal, an

Aligning the deflector plate^ The position of the deflector platecan be brought forward by up to35 mm using the adjusting screws oneither side of the

Vent ducting^If the on-site ventilation system doesnot have a non-return flap, then thenon-return flap supplied with theappliance must be fitted in th

Setting up for recirculationmodeIf site conditions are not suitable for thecooker hood to be used with airextraction, the appliance must be setup for

Important: To avoid the danger oftoxic fumes, please observe theWarning and Safety instructions.This is especially crucial when usingthe cooker hood a

–If the exhaust air is to be ducted intothe open air, the installation of atelescopic wall vent or roof vent(available as an optional accessory)is rec

Silencer(optional accessory)To achieve even further reductions innoise levels, a special silencer can befitted in the ducting system...with air extra

All electrical work should beundertaken by a suitably qualifiedand competent person in strictaccordance with current nationaland local safety regulati

The Miele DSM 400 control module canbe used to combine the cooker hoodwith other components.It enables the following:Potential free connectionThis can

Connected load* ...280WFan motor* ...180WHob lighting ...2x50WVoltage ... AC230VFrequency ...

39

This appliance complies with allrelevant local and national safetyrequirements. Inappropriate usecan, however, lead to personal injuryand damage to pr

Alteration rights reserved / 0613M.-Nr. 09 190 950 / 05

Technical safety~Before installation, check the cookerhood for visible signs of damage.Under no circumstances should youuse a damaged appliance. It co

~Do not connect the appliance to themains electricity supply by amulti-socket unit or an extension lead.These do not guarantee the requiredsafety of t

In order to ensure safe operation, andto prevent gases given off by theheating appliances from being drawnback into the room when the cookerhood and t

Correct use~Never use an open flame beneaththe cooker hood. To avoid the dangerof fire, do not flambé or grill over anopen flame.When switched on, the

~All ducting, pipework and fittingsmust be of non-flammable material.These can be obtained from the MieleSpare Parts department or frombuilders'