Miele KM 5773 Manuale Utente

Operating and Installation instructionsCeramic hobs with inductionKM 5773To avoid the risk of accidents ordamage to the appliance it isessential to re

Protecting the appliance fromdamageDo not drop anything on theceramic surface. Even a lightobject could cause damage in certaincircumstances.Do not us

Protection from burning andscaldingThe appliance gets hot when inuse and remains hot for quite awhile after being switched off. There isa danger of b

Appliance faultsIn the event of damage or a defect,switch off the appliance immedi-ately. Disconnect completely from theelectricity supply. If the app

Futher safety notesFor people fitted with a heartpacemaker:Please note that the area immediatelysurrounding the hob iselectromagnetically charged, and

Disposal of the packingmaterialThe transport and protective packinghas been selected from materials whichare environmentally friendly for disposaland

General notesYour appliance has a "programming"function which you can use tocustomise the appliance to yourparticular requirements (see"

Calibrating the sensorswitchesAutomatic calibrationTo ensure trouble free operation, thesensors–need to be recalibrated afterinstallation and each tim

How it worksAn induction coil is located under eachcooking zone. When a cooking zone isswitched on, this coil creates amagnetic field which impacts di

NoisesWhen using an induction cooking zone,the following noises can occur in thepan, depending on what it is made ofand how it has been constructed.–O

PansSuitable pans include:–stainless steel pans with a magneticbase–enamelled steel pans–cast iron pansUnsuitable pans:–stainless steel pans without a

Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Hob . . . . . . . . . . . . . . . .

Sensor switchesThis hob is equipped with electronicsensor switches which react to fingercontact.To operate a cooking zone, touch therelevant sensor sw

SettingsCooking process Power levels*standardfactory settings(12 levels)extendedsettings**(23 levels)Melting butterDissolving gelatine1 - 2 1 - 2.Warm

Auto heat-upWhen Auto heat-up has been activated,the cooking zone switches onautomatically at the highest power leveland then switches to the continue

How to activate Auto heat-up^While a 0 is lit up in the cooking zonedisplay, touch the - sensor until therequired continued cooking powerlevel appears

Booster functionAll of the cooking zones are equippedwith a booster function, i. e. an increasein the power level.If activated, the zones will operate

Switching off and residual heatindicatorsTo switch off a cooking zone:^Touch the - and + sensors for thezone you want to switch off at thesame time.A

IntroductionThe hob is fitted with:- Minute minder (Timer function)- Automatic switch-off for the cookingzones (Timer function)- Memory function.These

Switching a cooking zone offautomaticallyYou can set a time at the end of which agiven cooking zone will switch offautomatically. This automatic switc

Memory functionThe settings used on a particularcooking zone from switching on rightthrough to switching off can berecorded as a Memory programme. Upt

Using a Memory programmeThe same pan must be used in order toobtain the same cooking result as whenthe programme was recorded. Thequantity and size of

Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Safety lock . . . . . . . . .

Combi modeThe minute minder, automatic switch-offand memory functions can all be usedat the same time.If you wish to use the minute minder atthe same

Safety lockKeep children away from the hob fortheir own safety.Your appliance is equipped with asafety lock to prevent the hob and thecooking zones be

Stop and GoYour appliance has a Stop and Gofeature which, when activated, reducesthe power of all cooking zones thathave been switched on. This allows

Safety switch-offSafety switch-off with an over-longcooking timeYour hob is fitted with a safety switch-offfeature in case you forget to switch it off

Overheating protectionAll of the induction coils and the coolingelement for the electronics are fittedwith an overheating protectionmechanism. To prev

Do not use a steam cleaner to cleanthis appliance. The steam couldreach electrical components andcause a short circuit. Pressurisedsteam could also ca

Should any sugar, plastic oraluminium foil spill or fall on to a hotcooking zone while it is in use, firstswitch off the appliance. Then carefullyscra

You can change the standard settingsof your hob (see chart).Proceed as follows:^With the hob switched off, touch thehob ON/OFF sensor s and the safety

Programme* Status** SettingP0Demonstration mode andfactory default settingsS 0 Demonstration mode onS1 Demonstration mode offS 9 Factory default setti

Programme* Status** SettingP12Auto heat-up S 0 OffS1 Activated by selecting thepower level using -S 2 Activated by selecting thepower level using +S 3

HobControl panelabcde Cooking zonesSensor switchesf For setting the power levelg Boosterh Sensor for setting the timer, changingbetween functions, and

Installation work and repairs toelectrical appliances must only becarried out by a suitably qualifiedand competent person in strictaccordance with cur

... one of the following has occurred:–The booster has automaticallyswitched off early.–The set power level 10, 11 or 12 isalternating in the display

In the event of any faults which you cannot remedy yourself, or if the appliance isunder guarantee, please contact:–Your Miele dealer, or–the Miele Se

Safety instructions forinstallationFit wall units and extractor hoodbefore fitting the hob to avoiddamaging the surface.The veneer or laminate coating

Safety distance above the hobA minimum safety distance must bemaintained between the hob and thecooker hood above it. See the cookerhood manufacturer&

Safety distances to the sides of thehobIdeally the hob should be installed withplenty of space on either side. Theremay be a wall at the rear and a ta

Safety distance when installing the appliance near a wall with additionalniche claddingThere must be a minimum distance of 50 mm between the niche cla

Installation above an ovena Ventilation gap for the fanwhen installed in a base unit withouta back panel.When installed above a Miele ovenin a worktop

Building-in dimensionsa Frontb Building-in depthc Building-in depth for mains connection cabled Mains connection cable, L = 1,400 mmInstallation48

Preparing the worktop^Make the worktop cut-out followingthe dimensions applicable.Remember to maintain a minimumsafety distance of 50 mm from theback

Cooking zone displayn Displays:0 = Cooking zone ready for use1 to 12 = Power levels# = Residual heatß = No pan on cooking zone or pan unsuitable(see &

Sealant Do not use any sealant unlessexpressly instructed to do so. Thesealing strip under the edge of the toppart of the hob provides a sufficientsea

Electrical connectionAll electrical work should be carriedout by a suitably qualified andcompetent person, in strictaccordance with current local andn

WARNINGTHIS APPLIANCE MUST BEEARTHEDThe electrical safety of this appliancecan only be guaranteed whencontinuity is complete between it andan effectiv

Wiring diagramN.B. This appliance is supplied single phase only in the U.K. / AUS / NZInstallation53

54

55

Alteration rights reserved / 4806M.-Nr. 06 721 380 / 04en-GB

Timer/Memory displayr Indicator lamp for relevant zone, e.g. the rear right cooking zones Display for Time/Memory programme00 to 99 = TimeP1 to P5 = M

To avoid the risk of accidents anddamage to the appliance, pleaseread these instructions carefullybefore using it for the first time. Theycontain impo

Never open the casing of theappliance.Tampering with electrical connectionsor components is highly dangerous tothe user and can cause operationalfault

Safety with childrenUse the safety lock to preventchildren operating the appliance oraltering the settings.The appliance is only intended foruse by ad